TA3132-1
$18,360.00
Heli-Preheat kit – Bell 412/212 – 115V
Description
Heli-Preheat Kit – Bell, 212/412 with Pratt & Whitney, PT6T Twin Pac (PT6T-3/B/BE/BF/BG/D/DE/DF)
FAA-STC: # SR04132CH
TCCA-STC: # Acceptance of SR04132CH
Preheat is applied through electrical resistance heat in the form of thin pads sized and shaped to fit various parts. This includes engines, engine reduction gearboxes, attached accessories, main & tail rotor gearboxes, battery (standard configs), and oil/hydraulic tanks. Avionics are heated by a fan driven heater. Power is routed to elements through dedicated wiring assembly with circuit overload protection. Bell approved dual ground power door assembly is include. System is self-regulating. Heated components reach an average state of thermal equilibrium in approximately six hours.
This preheat kit when installed will supply 1162-1237 watts with a 10.1-10.8 amp draw at 115 volts for main preheat system.
Avionics heat (500 watts) on separate circuit that can be used to power additional ground powered devices up to 800 watts (7 amps @ 115 volt).
* Required Bonding sealant sold separately. Quantity 6, PN: TAU02788
* AVF0001 form requested for verification of purchase.
Additional Information
Heil Manufacturer: Bell
Helicopter Cylinders: N/A
Engine Manufacturer: Pratt & Whitney
Old Part Number: TAS300-34-DT-115, TSHB412-3132-115, TSHB412-3132-115
Voltage: 115
USA-Cert (8130-3 available): STC kit (YES)
Downloads
To access any of our Downloads (Documents) below, you will need to login or register for an account.
-
Drawing - Kit (System)
- 03132-115, System kit drawing for Bell 412&212 157.96 KB
-
Operator's guide
- TPG1000, Operating Guide General Preheat Kit 353.41 KB
-
ICA (Instructions for Continued Airworthiness)
- TCA1000, ICA General Preheat Kit (all kits) 269.97 KB
-
System Install Instructions
- TNH3132 System install instructions for Bell 412-212 9.09 MB
- TNG1000, Installation Guide 5.38 MB
-
Component Install Instructions
- TN02070, Flush Mount Plug Install Instructions 214.03 KB
- TN02533, Flush Mount Plug W/cap Install Instructions 141.28 KB
- TN02782, Click Bond Mount Install Instructions 381.67 KB
- TN02788, Bonding of Pad Element Install Instructions (was 186) 121.86 KB
- TN02793, Instruction for DT series connectors (was 192) 329.80 KB
- TN02800, Battery Heat Kit Install Instructions 1.41 MB
- TN03039, LED Indicator Light Install Instructions 101.52 KB
- TN03094, Instruction AV Heater 1.59 MB
- TN03097, Instruction 2 place Door kit 456.38 KB
-
Drawing - Cable Kit/Wire Diagram
- 03133, Cable Kit for Bell 412 and 212 148.79 KB
-
Component Install/Mod Drawing
- 03097, Drawing 2 place Door Kit 264.87 KB
- 03127, Drawing Connector Kit, 5 Contact 254.68 KB
- 03128, Drawing Bracket for Tailboom 253.08 KB
- 03140, Bracket shore power Bell 412, 212 351.86 KB
- 03141, Drawing/install Panel/Bracket mount fuse kit 111.63 KB
- 03142, Bracket AV/CABIN HEATER 243.23 KB
- 03143, Bracket assembly with nut plates 302.01 KB
- 03144, Drawing AV bracket install 342.04 KB
-
Eligibility (STC)
- SR04132CH, B412 USA STC 1.04 MB
- 5010-O-16-0666, TCCA STC Acceptance B412 114.19 KB
-
Forms
- AVF0001, Aircraft Verification Form 165.09 KB