TA3083-2
Part Number: TA3083-2
Engine Manufacturer: Honeywell (Garrett), Rolls Royce (Allison)
PRICE:
$12,600.00
Heli-Preheat Kit – Bell 407- STC – 230V
Description
Heli-Preheat Kit – Bell, 407 with Rolls Royce, RR250-C47 or HTS900 Eagle Conversion
FAA-STC: # SR03474CH
EASA-STC: # 10057671
TCCA-STC: # SH16-23
Preheat is applied through electrical resistance heat in the form of thin pads sized and shaped to fit various parts. This includes engine reduction gearboxes, attached accessories, main & tail rotor gearboxes, battery (based on RG-407 or RG-427), and oil/hydraulic tanks. Power is routed to elements through dedicated wiring assembly with circuit overload protection. Bell approved dual ground power door assembly is include with extra place for additional ground power. System is self-regulating. Heated components reach an average state of thermal equilibrium in approximately six hours.
This preheat kit when installed will supply 527.5 watts with a 2.3 amp draw at 230 volts.
Note: For 407HP with HTS900 Eagle Conversion, alternate configuration of pads for this engine supplies 580.5 watts with a 2.5 amp draw at 230 volts. Please specify when ordered.
* Required Bonding sealant sold separately. Quantity 2, PN: TAU02788
* AVF0001 form requested for verification of purchase.
Additional Information
Heil Manufacturer: Bell
Helicopter Cylinders: N/A
Engine Manufacturer: Honeywell (Garrett), Rolls Royce (Allison)
Old Part Number: TAS300-36-DT-230, TSHB407-2776-230,TSHB407-3087-230, TSHB407-3083-230
Voltage: 230
USA-Cert (8130-3 available): STC kit (YES)
Downloads
To access any of our Downloads (Documents) below, you will need to login or register for an account.
-
Drawing - Kit (System)
- 03083-230, System Kit drawing for Bell 407 256.31 KB
- TA3083-2, HPI DRAWING REV K 75.24 KB
-
System Install Instructions
- TNH3083 B407 System Kit Install Instructions 3.37 MB
-
Operator's guide
- TPG1000, Operating Guide General Preheat Kit 353.41 KB
-
ICA (Instructions for Continued Airworthiness)
- TCA1000, ICA General Preheat Kit (all kits) 269.97 KB
-
Component Install Instructions
- TNG1000, Installation Guide 5.38 MB
- TN02070, Flush Mount Plug Install Instructions 214.03 KB
- TN02782, Click Bond Mount Install Instructions 381.67 KB
- TN02788, Bonding of Pad Element Install Instructions (was 186) 121.86 KB
- TN02793, Instruction for DT series connectors (was 192) 329.80 KB
- TN02829, Circular Plug and Receptacle Install Instructions 812.54 KB
- TN03012, Instruction Junctions 358.47 KB
- TN03039, LED Indicator Light Install Instructions 101.52 KB
- TN03046, Instruction - Thermal Control 294.71 KB
- TN03095, Door kit 2 place 428.08 KB
- TN03273, instruction - door switch 257.86 KB
-
Component Install/Mod Drawing
- 03030, Connector Kit Drawing/Installation Instruction (14 contact) 317.17 KB
- 03095, 2 place door kit B407 200.03 KB
- 03125, Connector Kit DWG/Installation Instruction (6 contact) 376.23 KB
- 03141, Drawing/install Panel/Bracket mount fuse kit 111.63 KB
-
Drawing - Cable Kit/Wire Diagram
- 02774, Wire Routeing Drawing for Bell 206/407 214.08 KB
- 03082, Cable Kit Drawing for Bell 407 223.11 KB
-
Eligibility (STC)
- SR03474CH, Bell 407 USA (FAA) STC 198.78 KB
- 10057671, EASA STC for B407 2.02 MB
- SH16-23, TCCA-STC for B407 399.89 KB
-
Forms
- AVF0001, Aircraft Verification Form 165.09 KB
